RockyGuard RG5 Snow Guard

RockyGuard RG5 Snow Guard - Green
Buy Now at SnowGuardDepot.com

A snow guard typically installed on metal panel & metal shingle roofs.

Available in several finishes:

  • Powder Coated EG Steel
  • Mill Finish Aluminum
  • Copper
Product Prices
$5.50
Steel (Powder Coat)
$8.00
Copper

Snow Retention System: 

  • Clip Style Snow Guards

Product Category: 

Roof Type Category: 

  • Standing Seam Metal Panel

Related Products

Woodbinder Eclipse Screw

Woodbinder Eclipse screws include rubber grommets, especially designed as an exposed fastener for metal panel roof installations.
$0.27
Dark Bronze, Grey, Black
$0.37
Dark Bronze Stainless

Product Cut Sheet

RockyGuard RG5 Snow Guard Cut Sheet

Download Detailed Cutsheet (PDF): 
rmsg-rockyguard-rg5-snow-guard-cut-sheet.pdf

Materials List:

  • Powder Coated EG Steel
  • Powder Coated Aluminum
  • Mill Finish Aluminum
  • Copper
  • Cor-ten®

Notes:

  1. Snow guards are to be installed to manufacturer’s specifications.
  2. Contact manufacturer for selected layout.
  3. For custom materials contact manufacturer.
  4. Other sizes are available on a custom basis.

Installation Instructions

RockyGuard Layout Pattern Guide for Slate, Shake and Shingle Roofs

Layout pattern guide for Slate, Shate, Asphalt Shingle, Metal Shingle and Synthetic Slate and Shake Roofs

Instruction Steps:

1)

Minimum Rocky Guard Eave Row

The row at the eave is the minimum requirement for all roofs.  Rocky Guards are spaced approximately 12” O/C and are located on second course of roofing material at or near the load bearing wall. 

2)

Additional Rows (if required)

Additional rows of Rocky Guards may be necessary to stabilize the snow on longer roof decks, steeper roofs, slippery roof surfaces such as slate, synthetic products and metal and on roofs in heavy snow load areas.  

Contact Rocky Mountain Snow Guards for a recommended Rocky Guard layout if any of these factors are present.

Installed Product Image

Download Installation Instructions (PDF): 
rmsg-rockyguardlayoutpatternguide.pdf

Installation Notice

Note:   Roof support structure should always be reviewed to make sure that the additional snow held on the roof will not cause structural issues.  On asphalt shingle roofs less than 8/12 pitch where ground snow loads do not exceed 110 psf, additional rows are not required above the eave row.

Snow Guard Placement for Shingle Style Roofs

Guide for placing snow guards on various shingle-style roofs, like: asphalt shingle, title, slate, metal shingle and synthetic slate and shake.

Instruction Steps:

Less than a 6/12 Pitch

For roofs less than a 6/12 pitch, the distance between the butt end and the pad face must be a minimum of 3 times (3x) the thickness of the roofing material (x).

Greater than a 6/12 Pitch

For roofs greater than a 6/12 pitch, the distance between the butt end and the pad face must be a minimum of 6 times (6x) the thickness of the roofing material (x).

Download Installation Instructions (PDF): 
snow-guard-placement-guide-shingle-style-roofs.pdf

3-Part Specification

Download Specification Sheet (PDF): 
rg5-snow-guard-specification-sheet.pdf

Part 1 -GENERAL

1.1 SUMMARY

  1. WORK INCLUDES

    1. Install RG5 Snow Guard to roof system.
    2. Provide necessary components: RG10 Snow Guard and Fasteners (3 #12 Screws or 5 Nails).

1.2 RELATED SECTIONS

    1. Section 07310 Shingles
    2. Section 07410 Preformed Metal Roofing
    3. Section 07600 Flashing and Sheet Metal
    4. Division 7: Thermal and Moisture Protection

1.3 SYSTEM

  1. COMPONENTS:

    1. RG5 Snow Guard.
    2. Fasteners.
    3. Fastener Cover Clip (optional).
      1. Design - To be recommended by Manufacturer or Structural Engineer.

1.4 SUBMITTAL

  1. Submit manufacturer’s specifications, recommended layout, product drawings and installation instructions.

1.5 QUALITY ASSURANCE

  1.  Installer to be experienced in roofing and snow retention for a minimum of not less than 5 years.

1.6 DELIVERY/ STORAGE

  1. Inspect material upon delivery and order replacements if necessary. Store materials in dry covered area prior to installation.

PART 2 -PRODUCTS

2.1 MANUFACTURER

  1. Rocky Mountain Snow Guards, Inc., 2055 S. Raritan, Denver, CO 80223, 877-414-7606, www.rockymountainsnowguards.com

2.2 MATERIALS

  1. RG5 Snow Guard 14 gauge electro galvanized steel.
  2. Fasteners 2” zinc plated #14 screws.
  3. Fastener Cover Clip 22 Gauge electro galvanized steel (optional).

2.3 FINISH

  • TGIC Polyester powder coating

PART 3 – EXECUTION

3.1 EXAMINATION

  • Inspect roof structure and panel attachment to insure it will withstand snow loads. Correct all problems before installation of snow fence.

3.2 INSTALLATION

  • Install according to architects drawing and manufacturer’s instructions.
Get FREE Quote

Request Snow Guard or Snow Fence Layout & Quote

Get More Info

Request General Information or Pricing